Clipsal Max 4 Link Neutral 7Hole - L7/150
This item is currently available for backorder with an estimated arrival time of 2 days
Please note this ETA is provided to us by our suppliers and could potentially be delayed due to factors outside our control. If there are any delays we will contact you to keep you updated.
Choose your style, Select your Switch and Checkout
We can customise your powerpoint to a range of colours and layouts, suited to your needs.
Clipsal Max 4 Link Neutral 7Hole - L7/150
SKU | CLIL7/150 |
---|---|
Supplier No | L7/150 |
EAN / Barcode | 9318793006576 |
Standards | AS/NZS 60898 |
Width | 13 |
Height | 56.000000 |
Length | 165.000000 |
Width | 58.000000 |
Brand | Clipsal |
Range | Max4 |
Number of Poles | 1 Pole |
Voltage | 240 V |
Get Max 4 your buck
Complete protection with high performance. With Clipsal Max 4 you will find a range of enclosures, switchboards, residual current devices, miniature circuit breakers, isolators, distribution boards, overvoltage protection and accessories.
A FEW FAQS
L7/150 is 500V 370A 7 Hole Front Wiring Neutral Link. Black base and cover. Dimensions: 162 x 53 x 55mm. 2 tunnels, 17mm diameter accommodate 150mm2 cable. 1 tunnel, 15.5mm diameter accommodate 120mm2 cable. 2 tunnels, 10mm diameter accommodate 50mm2 cable. 2 tunnels, 5.9mm diameter accommodate 16mm2 cable. Supplied with Allen key. For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150
The link bar part number is L7/150 (neutral) or L7/150R (active) They will accommodate up to 150mm2 cable. L7/150 Neutral Link, Maxi, 7 Hole, 370A L7/150R Active Link, 7 Hole, 370A, Front Wiring, Black Base and Cover Front Wiring, Red Base and Cover For further information, please visit: https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150 https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150R
Yes the L13/150 will suit those requirements.
Issue: Although the BPH motors that are used with the Lexium 17 and 15 range of Servo drives are factory MSET, occasionally there may be a need to MSET this in the field due to commutation error being reported. Product Line: Lexium BPH Environment: Cause: Due to an incorrect offset value set in the drive, the drive may report a F25, commutation error. Resolution: This resolution discusses the MSET procedure for a BPH motor with a Lexium 17/15 series drive. Proper commutation and position feedback are required to interface a particular servo drive and motor combination. When using Schneider Electric BPH motors and Lexium drives, this setup (or “characterization”) process has been completed and verified for the user at the factory. Occasionally there may be a need to MSET the BPH motor and this is detailed in this procedure. Perform the following steps, as described, and in the order presented, to complete the MSET procedure. 1. Disconnect the Motor from the Mechanical Load 2. Electrical Connections A. Verify that the required electrical connections for drive power, logic power, motor power and resolver are as described in the Lexium drive user manual. B. Apply 24VDC logic and AC input power to confirm proper drive startup sequence and self-checks. Follow this MSET procedure only if the drive firmware is ver 5.51 and above. Connect to the drive using Hyperterm… Type OPMODE followed by Enter - note down the Opmode (xx) the drive is set to. Type OPMODE 2 followed by Enter - switch to digital torque mode C. Type 'EN' followed by Enter. D. Type "Zero" followed by ENTER - Motor shaft will jump to nearest pole. MPHASE value is automatically set. Type SAVE Type OPMODE xx followed by enter ( where xx is the default value that was originally set for the application.) G. Type COLDSTART (the drive will reboot) This completes the MSET procedure.