Unfortunately, we do not have an insulated version of 450VC. Depending on the requirement we have 238 mounting boxes or the black plastic insulating shroud which can be used with 450VC. Customer needs to ensure they are following the wiring regulation. For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=238 https://www.clipsal.com/Trade/search-results?q=insulating%20shroud 238

Yes, the 450VC will fit the WSC227/2. For more information, please refer to the link https://www.clipsal.com/Trade/Products/ProductDetail?catno=450VC

The 450VC-WE suits corrugated iron. This is compatible with all standard Bakelite series with 84mm centred mounting holes. Please go to the website via the following link https://www.clipsal.com/Trade/Products/ProductDetail?catno=450VC and check under the Documentation Tab for more information.

No, unfortunately we only have 450VC-WE which is a horizontal mounting block suitable for vertical corrugated iron.

Issue: Why is my Back-UPS ES giving a Constant tone with the Power on LED flashing? Product Line: BACK-UPS ES Environment: BE350G, BE450G, BE550G, BE650G1 and BE750G Cause: If this is a new installation confirm that the internal battery was connected properly. Refer to the user manual for instructions on this procedure. The Back-UPS ES performs an internal self-test every 14 days, the internal self-test checks the integrity of the battery. If the battery fails the self-test, the Power on LED will flash and the unit will emit a constant tone. This is a WARNING that the battery may be near the end of its life, replacement is typically recommended within 2-4 weeks. Resolution: Step 1: Verify that the UPS is not being overloaded: - The Back-UPS ES 350 can support 350VA or 200Watts on the battery powered outlets. - The Back-UPS ES 450 can support 450VA or 257Watts on the battery powered outlets. - The Back-UPS ES 550 can support 550VA or 330Watts on the battery powered outlets. - The Back-UPS ES 650 can support 650VA or 390Watts on the battery powered outlets. - The Back-UPS ES 750 can support 750VA or 450Watts on the battery powered outlets. APC recommends plugging only the computer and monitor in the battery powered outlets, other peripherals should be plugged into the ""Surge Only"" outlets on the labeled on the the UPS. Outlet strips or surge protectors should NEVER be plugged into any UPS. Remove any excessive load from the UPS. On the same note if the Back-UPS ES is close to being fully loaded (>80% of the battery outlet’s watt capacity) it is not recommended that the Back-UPS ES be used as a master on/off switch to turn on your equipment. Instead power the Back-UPS ES on, letting it complete its self-test before turning on the connected equipment. Step 2: A self test should be performed with the UPS fully charged (charging without interruption or transfer to battery for 5 hours) and normal load attached. To do this, power down all equipment attached to the battery outlets. Then reboot the Back-UPS ES by turning it off then count to 5 and power it back on. If the constant tone clears, then it was a false onbattery condition and the unit has been reset. It now is ready to be used again. Proceed to step 3 if it does not clear. Step 3: (proceed only if "step 2" does not clear the Replace Battery Condition) The Back-UPS ES comes with a 3 year warranty which includes the internal battery. If the Back-UPS ES was purchased within 3 years, please contact APC Support and reference the steps performed in this document. Also include the exact part number and serial number found on the bottom of the Back-UPS ES. If the Back-UPS ES is outside of the 3 year warranty, click HERE for upgrade and battery replacement options

Issue: Needs a ATV12 drive with 460V. Product line: ATV12, Altivar 12 Environment: All Cause: Customer wants the ATV12 drive for a 5HP, 460V motor. Resolution: The ATV12 model is only available for 208-230V motor. For 460V ratings, use the ATV312 or the ATV320 which has unit available up to 20HP, 460V.