359 is the locknut for 355 series screw. Size: 6 mm x 6 mm fits M3.5 x 0.8 mm pitch screws For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=359

The part number for the C-clip to suit 19-25mm gyprock/ plasterboard is 154/1. For 50mm screws to suit the part number is 355A (Thread M3.5 x 0.8 Pitch) For further information please visit https://www.clipsal.com/products/detail?CatNo=154/1&backto=%2Fsearch%3Fq%3D154%2F1&tab-document-1=0

Issue Can I extend the length of my Environmental Sensors and Probes? Product Line Environmental Monitoring Products NetBotz 250 NetBotz 355, 455, 450, 550, 570 Environmental Monitoring Unit/System Environment All serial numbers All firmware versions Cause This document pertains to the Environmental Sensors and Probes that can be connected to APC's Environmental Monitoring and Management Units (AP9312, AP9319, AP9320, and AP9340) and version 3 NetBotz Appliances. Resolution AP9512T/THBLK - We do not officially support lengthening the temperature humidity probe with PS/2 extension cables. However, though not officially supported, we have extended the length using two 12 foot PS/2 extension cables for a total of 36 feet. AP9335T - To increase the length, you must connect an additional Cat5 cable, connected via an RJ-45 coupler. AP9312, AP9319, AP9320, AP9340 - 50 ft. NetBotz 200 - 50 ft. NetBotz 250 - 50 ft. NetBotz 355, 455, 450, 550, 570 - 50 ft. AP9335TH - To increase the length, you must connect an additional Cat5 cable, connected via an RJ-45 coupler. AP9312, AP9319, AP9320, AP9340 - 50 ft. NetBotz 200 - 50 ft. NetBotz 250 - 50 ft. NetBotz 355, 455, 450, 550, 570 - 50 ft. AP9520T/TH - This sensor connects via A-link communication. The Alink protocol has a maximum distance of 1000 meters (3,280 ft). However, these sensors are connected via Cat5 cabling which has a functional limitation of 100m per length. For lengths longer than 100m, a repeater device is required to amplify the signal. Additional information on connecting Environmental Sensors and Probes can be obtained via the User's Manual for the AP9312, AP9319, AP9320, AP9340, and current NetBotz products.

Issue: What is compatible with a NetBotz Appliance? Product Line: NetBotz Appliance (250, 355, 450, 455, 570, & 750) Environment: NetBotz (all versions) Cause: This article explains in detail the entire NetBotz product line compatibility for Universal Sensors, Cameras, Rack Access, and Software. Resolution: NetBotz Appliance Compatibility Matrix https://www.apc.com/salestools/JHIN-7PTK7P/JHIN-7PTK7P_R8_EN.pdf?sdirect=true NetBotz Appliance Specifications Chart https://www.apc.com/salestools/JHIN-7PTKDA/JHIN-7PTKDA_R4_EN.pdf?sdirect=true NetBotz 250 Brochure https://www.apc.com/salestools/MKEY-ADCS74/MKEY-ADCS74_R1_EN.pdf NetBotz 750 Brochure https://www.apc.com/salestools/SBRN-B7CKMD/SBRN-B7CKMD_R0_EN.pdf

Issue: Why does the Camera POD 160A appear to not work with the NetBotz appliance it is connected to? Product Line: NetBotz v3 Wall Appliance: 455/456 (NBWL0455/6) NetBotz v3 Rack Appliance: 450/451 (NBRK0450/1), 550 (NBRK0550), & 570 (NBRK0570) NetBotz v3 Accessories: Camera POD 160A (NBPD0160A) Environment: NetBotz v3 (firmware below 4.6.2) NetBotz Camera POD 160A Cause: Newer NetBotz Camera Pods (NBPD0160A) are running a hardware revision that are not compatible with older NetBotz firmware. This causes the camera to appear failed and not register on the main NetBotz unit. Resolution: Updating the NetBotz appliance to firmware version 4.6.2 or later will correct the problem. If you have upgraded or are already running 4.6.2 or later and are still experiencing difficulties, contact technical support. Please note that this could also happen on a NetBotz 355A or 455A with the on-board camera with firmware prior to 4.6.2.. Verifying NetBotz Appliance Firmware Revision 1) Log into the NetBotz appliance using the Advanced View application. NOTE: For instructions on downloading Advanced View, see knowledge base FA230223. 2) Select the About tab. 3) The firmware revision will be listed in the Bootstrap Version field. Upgrade NetBotz Appliance Firmware Instructions on upgrading a NetBotz appliance firmware can be found within knowledge base FA158254.

Product Line IEC61850 Resolution There are a total of 355 data classes. The are divided into 7 categories as listed below: Data Classes Number 1. System Information 13 2. Physical Device Information 11 3. Measure ands 66 4. Metered Values 14 5. Controllable Data 36 6. Status Information 85 7. Settings 130